? coilcraft, inc. 2010 specifications subject to change without notice. please check our website for latest information. shielded power inductors C lps3314 document 541-1 document 541-1 revised 08/05/09 dcr srf i sat (a) 5 i rms (a) 6 inductance 2 max 3 typ 4 10% 20% 30% 20c 40c part number 1 20% (h) (ohms) (mhz) drop drop drop rise rise lps3314-102ml_ 1.0 0.062 215 1.8 1.9 2.0 1.6 2.10 lps3314-222ml_ 2.2 0.100 140 1.3 1.4 1.5 1.2 1.60 lps3314-332ml_ 3.3 0.145 115 1.1 1.2 1.3 1.0 1.35 lps3314-472ml_ 4.7 0.175 86 0.97 0.99 1.0 0.90 1.25 lps3314-562ml_ 5.6 0.220 74 0.92 0.95 0.98 0.82 1.10 lps3314-682ml_ 6.8 0.240 72 0.87 0.90 0.91 0.82 1.10 lps3314-822ml_ 8.2 0.270 60 0.58 0.75 0.78 0.70 1.00 lps3314-103ml_ 10 0.330 55 0.56 0.66 0.70 0.65 0.87 lps3314-153ml_ 15 0.440 45 0.46 0.56 0.59 0.62 0.82 lps3314-183ml_ 18 0.575 37 0.44 0.51 0.54 0.52 0.68 lps3314-223ml_ 22 0.720 34 0.44 0.48 0.49 0.45 0.60 lps3314-333ml_ 33 0.920 27 0.30 0.38 0.40 0.43 0.58 lps3314-473ml_ 47 1.40 22 0.28 0.33 0.34 0.35 0.47 lps3314-563ml_ 56 1.55 19 0.26 0.30 0.31 0.32 0.42 lps3314-683ml_ 68 1.80 17 0.22 0.26 0.29 0.30 0.40 lps3314-823ml_ 82 2.00 14 0.20 0.24 0.26 0.29 0.39 lps3314-104ml_ 100 2.75 13 0.19 0.23 0.24 0.24 0.32 lps3314-124ml_ 120 3.45 11 0.19 0.21 0.22 0.22 0.30 lps3314-154ml_ 150 4.10 10 0.16 0.19 0.20 0.20 0.27 lps3314-184ml_ 180 4.80 9.0 0.14 0.17 0.18 0.19 0.25 lps3314-224ml_ 220 6.00 7.0 0.14 0.16 0.17 0.16 0.22 lps3314-334ml_ 330 9.30 6.0 0.11 0.12 0.13 0.13 0.18 lps3314-474ml_ 470 12.0 4.5 0.080 0.11 0.11 0.12 0.16 lps3314-564ml_ 560 14.0 4.5 0.095 0.105 0.11 0.11 0.145 lps3314-684ml_ 680 18.5 4.0 0.092 0.100 0.105 0.095 0.125 lps3314-824ml_ 820 24.0 3.7 0.086 0.099 0.100 0.085 0.110 lps3314-105ml_ 1000 31.0 3.0 0.090 0.099 0.100 0.082 0.100 lps3314-155ml_ 1500 44.0 2.7 0.080 0.086 0.090 0.060 0.080 ? very low dcr; excellent current handling ? miniature 3.3 3.3 mm footprint; less than1.4 mm tall designer?s kit c330 contains 3 each of all values core material ferrite core and winding loss see www.coilcraft.com/coreloss terminations rohs compliant silver-palladium-platinum-glass frit. other terminations available at additional cost. weight 44.1 ? 46.5 mg ambient temperature ?40c to +85c with i rms current, +85c to +125c with derated current storage temperature component: ?40c to +125c. packaging: ?40c to +80c resistance to soldering heat max three 40 second reflows at +260c, parts cooled to room temperature between cycles moisture sensitivity level (msl) 1 (unlimited floor life at <30c / 85% relative humidity) failures in time (fit) / mean time between failures (mtbf) 38 per billion hours / 26,315,789 hours, calculated per telcordia sr-332 packaging 1000/7 reel; 3500/13 reel plastic tape: 12 mm wide, 0.3 mm thick, 8 mm pocket spacing, 1.52 mm pocket depth recommended pick and place nozzle od: 3.3 mm; id: 1.65 mm pcb washing only pure water or alcohol recommended 1. please, specify termination and packaging codes: lps3314-105m lc termination: l = rohs compliant silver-palladium- platinum-glass frit. special order: t = rohs tin-silver-copper (95.5/4/0.5) or s = non-rohs tin-lead (63/37). packaging: c =7 machine-ready reel. eia-481 embossed plastic tape (1000 parts per full reel). b = less than full reel. in tape, but not machine ready. to have a leader and trailer added ($25 charge), use code letter c instead. d =13 machine-ready reel. eia-481 embossed plastic tape. factory order only, not stocked (3500 parts per full reel). 2. inductance tested at 100 khz, 0.1 vrms, 0 ad using an agilent/hp 4263b lcr meter or equivalent. inductance at 1 mhz is the same for parts with srf 10 mhz. 3. dcr measured on a micro-ohmmeter. 4. srf measured using agilent/hp 8753es or equivalent. 5. dc current that causes the specified inductance drop from its value without current. 6. current that causes the specified temperature rise from 25c ambient. 7. electrical specifications at 25c. refer to doc 362 ?soldering surface mount components? before soldering.
? coilcraft, inc. 2010 specifications subject to change without notice. please check our website for latest information. shielded smt power inductors C lps3314 series document 541-2 document 541-2 revised 08/05/09 typical l vs current typical l vs frequency 0.130 0.004 3,30 0,10 0.130 0.004 3,30 0,10 0.0512 0.004 1,30 0,10 0.063 1,60 winding direction dash number internal code xxx x 0.146 3,70 0.146 3,70 0.104 2,65 0.104 2,65 recommended land pattern 0.063 1,60 0.098 2,50 0.098 2,50 0.024 0,60 45 typ 0.063 1,60 0.01 0.1 110 current (a) 0.1 1 10 10000 1000 100 inductance (h) 1 h 10 h 3.3 h 33 h 100 h 330 h 1000 h 0.01 0.1 110 frequency (mhz) 0.1 1 10 10000 1000 100 inductance (h) 1 h 10 h 3.3 h 33 h 100 h 330 h 1000 h current derating -40 -20 0 20 40 60 80 100 140 120 ambient temperature (c) percent of rated current 120 110 100 90 80 70 60 50 40 30 20 10 0 i sat i rms 25c dimensions are in inches mm
|
